Air Duct Repair in Austin, TX
We repair leaking, loose, crushed, and damaged duct runs across Austin.
A loose duct collar can start as a faint whistle at one vent. After a week, that room may stay warmer while cooled air escapes into an attic, crawlspace, or wall cavity. Over a season, a split return duct can also pull dust and unconditioned air into the system.
We look at the duct path, not just the room with weak airflow. A crushed flex duct, failed tape seam, or disconnected boot can make the blower run longer without delivering enough air to the register.
A rattling register grille can wait if the duct behind it is intact. A leak, disconnection, or collapsed run should not wait, because each cooling cycle sends conditioned air somewhere other than the room it is meant to serve.
Whistling vents and dusty rooms
You might hear a whistle when the system starts, feel little air from one ceiling vent, or notice that one bedroom never cools like the rest of the house. Some people call because a room gets dusty soon after cleaning, especially when the return grille is nearby.
You may also see a vent boot pulling away from the drywall, insulation around a ceiling register, or a flex duct that makes a thumping sound above the ceiling. A musty smell when the fan runs can point to air moving through an unsealed cavity rather than the intended return path.
Those symptoms can look alike from the room below, but they can come from different duct faults. A loose collar, damaged flex line, leaking boot, and return-side gap need different repairs and use different materials.
Duct inspection and leakage test
We start at the air handler, then check the supply plenum, return plenum, accessible flex duct, metal runs, collars, boots, dampers, and register connections. We look for separated joints, crushed sections, missing insulation, old tape, and duct runs resting on sharp framing.
A basic visual and airflow check commonly takes 30 to 60 minutes. When the duct path allows it, we compare airflow at registers and check static pressure near the blower to help locate a restriction or major leak.
We can often reseal an accessible joint, reconnect a collar, support a sagging run, or replace a short damaged flex section during the visit when the needed material is available. A concealed run, a custom sheet-metal transition, or ductwork behind finished drywall may need measurements first and a separate repair visit.
Access panels and duct material
The location of the damaged run matters. A joint beside an attic hatch is different from a boot above a high ceiling or a duct buried under insulation, and difficult access can add setup and repair time.
Duct material also changes the work. Flexible duct may need a new section and insulation jacket, while a metal trunk line may need a fitted patch, screws, mastic, or a replacement transition.
The age and condition of the surrounding ductwork matter too. If several seams have failed or an older flex run has become brittle, a small visible tear may not be the only section worth addressing. If a larger alteration needs local approval or an inspection, that also affects the scope before work begins.
Air handler label and vent location
Before you call, find the room where airflow changed and note whether the problem is at a supply vent or a return grille. If you can safely see the attic or closet access, tell us whether there is a clear path to the duct run.
The model number on the air handler label is useful, and it is often printed on the cabinet near the electrical panel or blower door. Let us know if the system is running now, if a vent is blowing at all, and whether you can hear air moving above the ceiling.
If you have seen a loose duct, take note of whether it is flexible insulated duct or metal pipe. Call us at (737) 239-8011 before a leaking run keeps sending cooled air, attic dust, or warm outdoor air into the wrong space.
When we are open
- Monday Open 24 hours
- Tuesday Open 24 hours
- Wednesday Open 24 hours
- Thursday Open 24 hours
- Friday Open 24 hours
- Saturday Open 24 hours
- Sunday Open 24 hours
Next
Next: blower motor replacement, or back to the home page.
